Lion Beautiful Auto Dispenser 200ml
Refillable clean medicated foam hand soap dedicated auto dispenser that can be used for refilling as usual → Refillable type that can be used for refilling → Running cost is low, and plenty of high quality foam that can be obtained anywhere comes out → Plenty of high-quality foam (.ml) that is better than existing foam. Sensor Sensitivity is good and can be used without stress. Beautiful medicated foam hand soap with refill
Ingredients / quantity [Active ingredient] Isopropylmethylphenol [Other ingredients] PG, sorbit solution, lauric acid, K hydroxide, coconut oil fatty acid acylglycine K solution, myristic acid, monoethanolamine, fragrance, polyoxyethylene tridecyl ether, EDTA, Dimethyldiallyl ammonium chloride / acrylamide copolymer liquid, benzyl alcohol, red 106 Usage and dosage (Preparation) How to insert the dry cell Check Close the lid of the liquid tank part tightly. Remove the dry cell cover at the bottom of the main unit. Turn off the power when replacing the battery. Set the included dry cell book as shown in the figure. Close the dry cell cover. Pay attention to the orientation of the batteries. When the battery level is low, the normal blinking flashes when the power is turned on, so replace it with a new battery. When replacing the batteries, replace them with new alkaline batteries. Put in a beautiful medicated foam hand soap. Perform with the power off. If you put a hand soap other than the clean medicated foam hand soap, the foam will not come out or it may cause a malfunction. Press the power button to turn it off. Slide the tank cover on the top of the main unit to remove it. Turn the lid of the internal tank counterclockwise to remove it. Insert the foam hand soap. Insert the spout into the tank so that it does not spill. Refill the upper limit line. Close the tank lid tightly clockwise. Slide the tank cover on the top of the main unit to close it. Press the power button to turn it on. Press to blink blue. How to use How to use Use with the power turned on. If you hold your palm up under the nozzle to receive the foam, the foam-like hand soap will come out automatically. If you hold your hand far from the sensor, the hand soap may not come out. Do not let the sensor part get wet directly or get the hand soap on it. (There is a risk that the sensor will not respond.) When the chemical solution is low, see Putting a clean medicated foam hand soap and replenish it. About care and storage For safety, we will do it with the power off. For safe use, clean it if it is difficult for bubbles to form or if it is extremely dirty. If it is very dirty, squeeze a cloth soaked in water-diluted hand soap and wipe it off, then finish with a soft, dry cloth. The hand soap may be solidified (if it becomes difficult for bubbles to come out). In that case, use a towel moistened with lukewarm water to remove the hardened hand soap. Do not let the sensor part get wet directly or get the hand soap on it. Caution If you do not use the product for a long time, turn off the power and remove the battery for safety. This product is not completely waterproof. Please do not wash it completely. When cleaning, be careful not to get it wet except inside the tank. Do not wipe with volatile substances such as thinner or benzine. (It may cause deformation, discoloration, or damage.)
JAN: 4903301321347
Ingredients / quantity [Active ingredient] Isopropylmethylphenol [Other ingredients] PG, sorbit solution, lauric acid, K hydroxide, coconut oil fatty acid acylglycine K solution, myristic acid, monoethanolamine, fragrance, polyoxyethylene tridecyl ether, EDTA, Dimethyldiallyl ammonium chloride / acrylamide copolymer liquid, benzyl alcohol, red 106 Usage and dosage (Preparation) How to insert the dry cell Check Close the lid of the liquid tank part tightly. Remove the dry cell cover at the bottom of the main unit. Turn off the power when replacing the battery. Set the included dry cell book as shown in the figure. Close the dry cell cover. Pay attention to the orientation of the batteries. When the battery level is low, the normal blinking flashes when the power is turned on, so replace it with a new battery. When replacing the batteries, replace them with new alkaline batteries. Put in a beautiful medicated foam hand soap. Perform with the power off. If you put a hand soap other than the clean medicated foam hand soap, the foam will not come out or it may cause a malfunction. Press the power button to turn it off. Slide the tank cover on the top of the main unit to remove it. Turn the lid of the internal tank counterclockwise to remove it. Insert the foam hand soap. Insert the spout into the tank so that it does not spill. Refill the upper limit line. Close the tank lid tightly clockwise. Slide the tank cover on the top of the main unit to close it. Press the power button to turn it on. Press to blink blue. How to use How to use Use with the power turned on. If you hold your palm up under the nozzle to receive the foam, the foam-like hand soap will come out automatically. If you hold your hand far from the sensor, the hand soap may not come out. Do not let the sensor part get wet directly or get the hand soap on it. (There is a risk that the sensor will not respond.) When the chemical solution is low, see Putting a clean medicated foam hand soap and replenish it. About care and storage For safety, we will do it with the power off. For safe use, clean it if it is difficult for bubbles to form or if it is extremely dirty. If it is very dirty, squeeze a cloth soaked in water-diluted hand soap and wipe it off, then finish with a soft, dry cloth. The hand soap may be solidified (if it becomes difficult for bubbles to come out). In that case, use a towel moistened with lukewarm water to remove the hardened hand soap. Do not let the sensor part get wet directly or get the hand soap on it. Caution If you do not use the product for a long time, turn off the power and remove the battery for safety. This product is not completely waterproof. Please do not wash it completely. When cleaning, be careful not to get it wet except inside the tank. Do not wipe with volatile substances such as thinner or benzine. (It may cause deformation, discoloration, or damage.)
JAN: 4903301321347
